M2 Hangupcause Codes
From Kolmisoft Wiki
Jump to navigationJump to search
| Code | Explanation |
| 300 | Not authenticated (accountcode = 0) |
| 301 | Originator not found by IP address |
| 302 | Global Call Limit reached |
| 303 | Originator Capacity reached |
| 304 | Originator's CPS Limit reached |
| 305 | Source (CallerID) not accepted by regexp |
| 306 | Originator Balance Limit reached (Balance Min) |
| 307 | Originator Rate not found |
| 308 | Dial Peer not found |
| 309 | Origination Point is not active |
| 310 | Suitable Terminator not found |
| 311 | User is blocked |
| 312 | Caller canceled the call |
| 313 | User call limit reached |
| 314 | M4 radius server did not receive accounting start packet (acct start timeout) |
| 315 | M4 radius server did not receive accounting stop packet (acct stop timeout) |
| 316 | M4 did not find termination point details |
| 317 | Registration to termination point failed |
| 318 | Originator codecs are not allowed |
| 319 | M4 can not make more calls |
| 320 | Balance too low to make a call |
| 321 | Caller's source number (CallerID) does not match terminator's source regexp |
| 322 | Caller's source number (CallerID) is denied by terminator's source deny regexp |
| 323 | Terminator's balance limit reached (balance max) |
| 324 | Rate margin is lower than allowed |
| 325 | Destination number is in blacklist |
| 326 | Destination number is not in the whitelist |
| 327 | Terminator's capacity reached |
| 328 | Terminator's user's call limit reached |
| 329 | Terminator's CPS limit reached |
| 330 | Destination is blocked in Originator's Tariff |
| 331 | Destination is blocked in Terminator's Tariff |
| 332 | Originator was found by IP but tech prefix does not match |
| 333 | Originator was found by IP but the port does not match |
| 334 | Source number is in blacklist |
| 335 | Source number is not in the whitelist |
| 336 | Destination can not be empty |
| 337 | Call comes from the server which is not assigned to the originator |
| 338 | Unreachable Terminator skipped (Periodic Check is enabled) |
| 339 | User is not allowed to dial through own terminators |
| 340 | User's call rate is higher than allowed |
| 341 | Originator's IP is unknown |
| 342 | Global Incoming System CPS limit reached |
| 343 | Too many hops |
| 344 | Terminator reached call limit in a Dial Peer |
| 345 | Terminator reached CPS limit in a Dial Peer |
| 346 | Call terminated by hangup command |
| 347 | Duplicate CallID/UniqueID |
| 348 | MySQL query timeout |
| 349 | Vendor is blocked |
| 350 | MNP search error |
| 351 | MNP CIP does not match TP |
| 352 | User daily spend limit reached |
| 353 | LNP search error |
| 354 | CLI/ANI is not in whitelist |
| 355 | CLI/ANI is in blacklist |
| 356 | CLD/DNIS is not accepted by regexp |
| 357 | CLD/DNIS is not in whitelist |
| 358 | CLD/DNIS is denied by regexp |
| 359 | CLD/DNIS is in blacklist |
| 360 | FROM domain is not allowed |
| 361 | TO domain is not allowed |
| 362 | Terminator balance limit reached (balance min) |
| 363 | DID is not active |
| 364 | DID is not forwarded anywhere |
| 365 | DID CC limit reached |
| 366 | DID selling rate not found |
| 367 | DID buying rate not found |
| 368 | Balance too low to make a DID call |
| 369 | DID authorization error |
| 370 | Flat-Rate authorization error |
| 371 | TP rate is higher than allowed in Flat-Rate |
| 372 | DID subscription is not active |
| 373 | DID selling rate is blocked |
| 374 | DID buying rate is blocked |
| 375 | Duplicate Call |
| 376 | Source number not found in TP CLI Whitelist Number Pool |
| 377 | Source number found in TP CLI Blacklist Number Pool |
| 378 | Destination number does not match TP CLD Whitelist Regexp |
| 379 | Destination number not found in TP CLD Whitelist Number Pool |
| 380 | Destination number matches TP CLD Blacklist regexp |
| 381 | Destination number found in TP CLD Blacklist Number Pool |
| 382 | CLI not found in User's allowed DIDs |
All M2 HGC return SIP 503 by default.
This can be changed in /etc/m2/system.conf using
hgcX = code
Where X is M2 HGC, and code is ITU-T Q.850 Code and then execute the command:
m2 reload
