M4 Alerts

From Kolmisoft Wiki
Revision as of 10:40, 29 November 2022 by Admin (talk | contribs) (Admin moved page M2 Alerts to M4 Alerts)
Jump to navigationJump to search

WIP

Description

Alerts is located under SECURITY -> Alerts

Alerts functionality is dedicated to taking actions about your system issues which may cause a problem. For example, you may block a User, disable Origination/Termination Point or simply send a notification to a specified Group of Contacts.

Parameters

You are able to follow these parameters:

  • ASR – Answer-Seizure Ratio (percent)
  • ACD – Average Call Duration (in seconds)
  • PDD – Average Post Dial Delay. The time between punching in the last digit of a telephone number and receiving a ring or busy signal (in seconds)
  • TTC (Time to Connect)(DURATION-BILLSEC) – Average time between receiving a ring signal and answer to the call (in seconds)
  • BILLSEC – Sum of calls bilsec (in seconds)
  • TOTAL CALLS – Sum of all calls.
  • ANSWERED CALLS – Sum of answered calls.
  • NOT ANSWERED CALLS – Sum of not answered calls (FAILED, BUSY, NO ANSWER).
  • SIMULTANEOUS CALLS – Number of simultaneous calls (only applies to users and providers).
  • PRICE SUM – Sum of calls price (only applies to users and providers).
  • HGC (ABSOLUTE) – Number of calls terminated with this HGC.
  • HGC (PERCENT) – Percentage of calls terminated with this HGC.

And it is possible to make actions for these types of M2 Objects or send notification about it:

Object Types



Primary and Secondary Object

If the Primary Object is Origination or Termination point, it is possible to select a Secondary Object. Secondary Object's Type can be only Destination or Destination Group. This allows selecting only a specific Destination or Destination Group for a particular Termination/Origination Point.

User to Notify

When the Object Type is a Client you have an option to Notify User(s) by email. An email goes to one of the preset email addresses:

  • Usually email is sent to NOC email address.
  • If NOC email address is not set, email is sent to Main email address.
  • If Main email address is not set, email is sent to Billing email address.
  • If Billing email address is not set, email is sent to Rates email address.
  • If none of NOC, Main, Billing or Rates email is set, no Alert notification email will be sent.



Settings


General

M2 alert general.png

  • Alert Name – name of Alert.
  • Primary Object - Primary Object to observe. All alerts must have a Primary Object.
  • Object Type – select Object Type to observe for Primary Object.
  • Object Name – specify name/prefix of Primary Object (fields depends on selected Object Type)
  • Secondary Object - Secondary Object to observe. Only Available if Primary Object's Type is Termination Point or Origination Point. Secondary Object act as Destination/Destination Group filter for Primary Object.
  • Object Type – select Object Type to observe for Secondary Object. Available types are Destination and Destination Group.
  • Object Name – specify name/prefix of Secondary Object.


  • Parameter – choose which parameter should be followed.
  • Check last – the time period to check.

NOTE: Object Type, Object Name, Parameter cannot be changed once Alert is created.

  • Ignore if Calls (in 1 h) <= – indicate calls sum when system should ignore Alert if calls sum in one hour is less than written (if 0, Alert will not be ignored).
  • Ignore if Calls (in 1 h) >= – indicate calls sum when system should ignore Alert if calls sum one hour is more than written (if 0, Alert will not be ignored).
  • Group to Notify – select Group of Contacts who should be informed about Alert/clear.
  • Notify to User – it is available only when the Alert object type is Client or Origination/Termination Point. Check if you want to notify User on Alert. More information available here.



Alert

M2 alert alert.png

  • Alert if <= - triggers the alert when observed parameter drops below given value.
  • Alert if >= - triggers the alert when observed parameter raises above given value.
  • Disable Primary Object - disables the observed primary object when an alert is triggered. NOT available for Destinations and Destination Group-type objects.
  • Disable TP in Dial Peer - disables the selected Termination Point when an alert is triggered (only available when observing the Termination Point object). This option does not have any effect when "Disable Primary Object" is enabled.
  • Routing Group - sets the provided Routing Group for the observed object (only available when observing Origination Points)
  • Deactivate DP in RG: - deactivates selected Dial Peer in Origination Point's Routing Group (only available when observing Origination Points)
  • Notify on Alert via email - sends a notification email when an alert is triggered.
  • Notify On Alert via SMS - sends a notification SMS when an alert is triggered. Because of functionality limitations, it can not work with some countries' mobile numbers.
  • SMS Alert Text - SMS text to send when alert is triggered. Active only if Notify On Alert via SMS: set to yes



Clear

M2 alert clear.png

  • Disable Clear - disables clearing indefinitely. The changes triggered by the alert can be changed by hand.
  • Clear on Condition
    • Clear if <= - clears the alert when observed parameter drops below given value.
    • Clear if >= - clears the alert when obsered parameter raises above given value.
  • Clear on time basis
    • Clear after - clears the alert after a given period of time. (The period is set once the alert is triggered)
    • Clear on Date - clears the alert on the given date.
  • Enable Primary Object - enables the Primary Object once the alert is cleared. Only available if Disable Primary Object is selected in the Alerts section.
  • Enable TP in Dial Peer - enables Termination Point to be used again in the corresponding Dial Peer (only available when observing Termination Point object).
  • Routing Group - sets the provided Routing Group for the observed object(only available when observing Origination Points)
  • Activate DP in RG: - activates Dial Peer in Routing Groug (the one disabled in Deactivate DP in RG: setting on Alert section). Only available when observing Origination Points.
  • Notify on Alert via email - sends a notification email when an alert is cleared.
  • Notify On Alert via SMS - sends a notification SMS when an alert is cleared.
  • SMS Alert Text - SMS text to send when alert is cleared. Active only if Notify On Alert via SMS: set to tyes




Examples

Block Termination Point for 1 hour if ACD during last 24h drops below 120 seconds

Primary Object, Object Type: Termination Point

Object name: select specific Termination Point

Parameter: ACD

Check Last: 24h

Ignore if Calls (in 24 h) <=: 50

Alert if ASR <=: 120

Disable Primary Object: checked

Disable Clear: unchecked

Clear on time basis, Clear after: 60 minutes

Enable Primary Object: checked