MOR and Trixbox

MOR and Trixbox (FreePBX) can't work nicely on the same server, because they use same Asterisk .conf files, which makes a lot of mess.

In order to integrate Trixbox with MOR you need to connect in the following way:

Connection diagram

As an example, we will configure one phone dialing. The phone is connected to Trixbox, which is connected to MOR:

Here, for simplicity, all the devices are in the same LAN:

• MOR server has IP: 10.10.1.10.
• Trixbox: 10.10.1.20.
• Phone: 10.10.1.30.

MOR and Trixbox are connected with the following settings:

• username: mor_trixbox.
• password: mor_trixbox_psw.

The phone to Trixbox is connected with:

• username: 201
• password: 201psw

Dialing from the phone to MOR

• Here the device makes a call to example destination 9999999999.
• When the call reaches Trixbox, the correct CallerID number for this phone is applied. In our example it is 1111111111. Then the call is forwarded to MOR.
• When MOR gets the call, it sees that the call was sent by Trixbox.
• MOR sees that Trixbox is Trunk with ANI. This means that MOR needs to check the CallerID of the call to find the real caller.
• MOR checks for the CallerID number (1111111111) and sees that this CallerID is assigned to a phone device.
• MOR retrieves all info (LCR/Tariff/Rates/Providers/etc) that is necessary to send the call further.
• When the call is finished, it is logged in MOR, not for Trixbox, but for the phone's user/device. That is what we wanted from our configuration.

Trixbox configuration for phone

Let's connect a phone to Trixbox. In FreePBX, create an extension for 201 phone:

Most important details:

Here we set CallerID number which should be applied to the call from this device. Password and dial string also here.

Trixbox configuration for MOR

In Trixbox we need to define MOR as a Trunk:

Define some route in Trixbox to use this Trunk (here is just an example):

Trixbox Trunk Troubleshooting

When passing multiple CallerIDs from multiple extensions in TrixBox through a single ANI-enabled trunk to MOR, make sure to define the outbound TrixBox PEER CallerID as empty using callerid="" <>.

If you don't include this, your MOR trunk will publish whichever CallerID was last passed to it. This will not allow you to correctly track different users' CallerID in MOR to provide them with separate call cost tracking.

Also, be sure NOT to define the inbound USER CalleID on the same TrixBox trunk with the same empty entry. If you do, the CallerID will be stripped from all incoming calls

MOR configuration for Trixbox

We need to create connection between MOR and Trixbox. In this example we will configure MOR-Trixbox connection using SIP.

We need to create user for Trixbox - pbx_user, put any details for it - it does not matter:

Now we need to configure device for Trixbox:

Main settings are:

• Mark this device as Trunk with ANI support
• Username (by example): mor_trixbox
• Password: mor_trixbox_psw
• Host: 10.10.1.20
• Make sure Dynamic? is unchecked and port is 5060 (for SIP)

MOR configuration for phone

To correctly bill phone calls you need to create separate user and device for it on MOR.

First let's create user for phone (phone_user):

Make sure you configure this user correctly - e.g. enter password/LCR/Tariff and other necessary details - this user will be used for real dialing out.

Then we need to create virtual device for our phone:

All settings for this device are not important at all except:

1. Make sure you marked this device as Trunk - important for receiving calls
2. Make sure you have good password for security
3. Make sure this devices host = dynamic (for security reasons to do not let you entr Trixbox IP here, because 201 is not Trixbox!)

CallerID for phone in MOR

In order MOR to recognize device/phone we need to assign CalledID to our phone's device:

NOTE: currently it is not possible to enter same CallerID as device's name. That way call will fail. It is due to the way Asterisk handles authentication.

Dialing to phone using DID

• Here call is coming to DID: 2222222222
• When it reaches MOR - MOR knows that 2222222222 should be forwarded to device 201
• Device 201 forwards call to Trixbox device: Dial(SIP/22222222222@mor_trixbox)
• Trixbox receives call with destination 2222222222
• Trixbox know that this call should be forwarded to phone SIP/201
• Phone rings
• After call in MOR log call is in device's 201 logs (CDR) - as it should be

MOR configuration

You need to create DID 2222222222 in MOR and assign phones user/device to this DID:

And in this device's Call Flow you need to forward call to Trixbox:

Trixbox configuration

Now when call arrives in Trixbox, it should know how to route call to phone 201.

We can configure this in 2 ways:

• Using Direct DID
• Using Inbound Route

Direct DID configuration

Inbound Route configuration

Final notes

Here as an example we used DID 2222222222 and CallerID 1111111111. In most cases in real installations these values are the same. That means - if user is dialing out and his CallerID (for example is) 3333333333 then he can receive calls by DID: 3333333333. You can configure this in same way using this manual. Different values for DID and CallerID here are chosen to make example more understandable.

Configuring more phones

In order to configure more phones:

1. Connect phone to Trixbox
2. Configure user/device in MOR for phone
3. Make sure CallerID for phone in Trixbox is the same as CallerID (CID) for phone's device in MOR
4. Create DID for phone on MOR, assign it to phone's device, forward call from device to Trixbox in MOR
5. Make sure Trixbox knows how to route call from DID to phone

Limitations

Using this configuration to connect Trixbox (FreePBX actually) to MOR has some limitations:

1. MOR device's CallerID can't be the same as device's name
2. Phones connected to Trixbox can't have similar CallerIDs. Actually they can - but MOR will not be able to distinguish which device is actually making a call - so these devices with identical CallerIDs will be billed together using one account (user/device) in the MOR

Errors

chan_sip.c:8373 check_auth: username mismatch, have <201>, digest has <mor_trixbox>

Error is made when configuring connection between MOR and Trixbox.

--note--

This is not a connection problem. This happens when you have incorrect or no outbound caller ID set within trixbox. Thus "201" (the display name)is being passed through to Mor.

--VCCS