Difference between revisions of "Conference with MOR + Trixbox"

From Kolmisoft Wiki
Jump to navigationJump to search
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
'''IT IS NOT POSSIBLE RUN CONFERENCE ONLY WITH MOR, YOU NEED EXTERNAL SOFTWARE, LIKE TRIXBOX'''
'''IT IS NOT POSSIBLE RUN CONFERENCES ONLY WITH MOR. YOU NEED EXTERNAL SOFTWARE, SUCH AS TRIXBOX.'''


'''Tested with 0.7, 0.8 MORs and 2.6.2.3 trixbox.'''
'''Tested with 0.7, 0.8 MORs and 2.6.2.3 Trixbox.'''




Line 7: Line 7:




First of all you need a user and device in [http://www.kolmisoft.com/billing-and-routing/ MOR] for a DID channel. Make sure you use IP authentication and use the exact settings in the image below (change 192.168.0.165 to Trixbox's ip address and Trunk? should be set to Yes).
First of all you need a user and device in [http://www.kolmisoft.com/billing-and-routing/ MOR] for a DID channel. Make sure you use IP authentication and use the exact settings in the image below (change 192.168.0.165 to Trixbox's IP address, and Trunk? should be set to Yes).
 


[[Image:device2.png]]
[[Image:device2.png]]


Create a DID and map it to the device.
Create a DID and map it to the device.


[[Image:didmap.png]]
[[Image:didmap.png]]


== Settings for Trixbox ==
== Settings for Trixbox ==


Log in as administrator to Trixbox and create a Trunk with the following settings: Change 192.168.0.148 to your MOR server IP address and 1005 '''username and secret''' to the appropriate settings.
Log in as administrator to Trixbox and create a Trunk with the following settings: Change 192.168.0.148 to your MOR server IP address and 1005 '''username and secret''' to the appropriate settings.


[[Image:trixboxtrunk.png]]
[[Image:trixboxtrunk.png]]


Create Conference with these settings:
 
Create a Conference with these settings:
 


[[Image:conference.png]]
[[Image:conference.png]]


Then create a DID (Inbound route):
Then create a DID (Inbound route):


[[Image:DID1.png]]
[[Image:DID1.png]]
[[Image:DID2.png]]
[[Image:DID2.png]]


Then try to call from any device to 8000 in MOR. You should hear a woman's voice and instructions on what you need to do.
Then try to call from any device to 8000 in MOR. You should hear a woman's voice and instructions on what you need to do.


Of course, if you change settings everywhere from 8000 to your real DID, it will work as well.
Of course, if you change settings everywhere from 8000 to your real DID, it will work as well.
== A few Hints ==
For each new conference room you will need a separate device and a DID in MOR.

Latest revision as of 15:26, 6 May 2012

IT IS NOT POSSIBLE RUN CONFERENCES ONLY WITH MOR. YOU NEED EXTERNAL SOFTWARE, SUCH AS TRIXBOX.

Tested with 0.7, 0.8 MORs and 2.6.2.3 Trixbox.


Settings for MOR

First of all you need a user and device in MOR for a DID channel. Make sure you use IP authentication and use the exact settings in the image below (change 192.168.0.165 to Trixbox's IP address, and Trunk? should be set to Yes).


Device2.png


Create a DID and map it to the device.


Didmap.png


Settings for Trixbox

Log in as administrator to Trixbox and create a Trunk with the following settings: Change 192.168.0.148 to your MOR server IP address and 1005 username and secret to the appropriate settings.


Trixboxtrunk.png


Create a Conference with these settings:


Conference.png


Then create a DID (Inbound route):


DID1.png


DID2.png


Then try to call from any device to 8000 in MOR. You should hear a woman's voice and instructions on what you need to do.

Of course, if you change settings everywhere from 8000 to your real DID, it will work as well.

A few Hints

For each new conference room you will need a separate device and a DID in MOR.