Difference between revisions of "M2 Hangupcause Codes"

From Kolmisoft Wiki
Jump to navigationJump to search
Line 54: Line 54:
| 325 || Destination number is in blacklist
| 325 || Destination number is in blacklist
|-
|-
| 326 || Destination number is not in whitelist
| 326 || Destination number is not in the whitelist
|-
|-
| 327 || Terminator's capacity reached
| 327 || Terminator's capacity reached
Line 68: Line 68:
| 332 || [[Originator was found by IP but tech prefix does not match]]
| 332 || [[Originator was found by IP but tech prefix does not match]]
|-
|-
| 333 || Originator was found by IP but port does not match
| 333 || Originator was found by IP but the port does not match
|-
|-
| 334 || Source number is in blacklist
| 334 || Source number is in blacklist
|-
|-
| 335 || Source number is not in whitelist
| 335 || Source number is not in the whitelist
|-
|-
| 336 || Destination can not be empty
| 336 || Destination can not be empty
|-
|-
| 337 || Call comes from servers which is not assigned to originator
| 337 || Call comes from the server which is not assigned to the originator
|-
|-
| 338 || Unreachable Terminator skipped (Periodic Check is enabled)
| 338 || Unreachable Terminator skipped (Periodic Check is enabled)

Revision as of 16:06, 19 December 2019

Code Explanation
300 Not authenticated (accountcode = 0)
301 Originator not found by IP address
302 Global Call Limit reached
303 Originator Capacity reached
304 Originator's CPS Limit reached
305 Source (CallerID) not accepted by regexp
306 Originator Balance Limit reached (Balance Min)
307 Originator Rate not found
308 Dial Peer not found
309 HGC NOT ASSIGNED
310 Suitable Terminator not found
311 User is blocked
312 Caller canceled the call (Freeswitch HGC ORIGINATOR_CANCEL 487)
313 User call limit reached
314 M2 radius server did not receive accounting start packet (acct start timeout)
315 M2 radius server did not receive accounting stop packet (acct stop timeout)
316 Freeswitch did not find termination point details
317 Registration to termination point failed
318 Originator codecs are not allowed
319 M2 can not make more calls
320 Balance too low to make a call
321 Caller's source number (CallerID) does not match terminator's source regexp
322 Caller's source number (CallerID) is denied by terminator's source deny regexp
323 Terminator's balance limit reached (balance max)
324 Rate margin is lower than allowed
325 Destination number is in blacklist
326 Destination number is not in the whitelist
327 Terminator's capacity reached
328 Terminator's user's call limit reached
329 Terminator's CPS limit reached
330 Destination is blocked in Originator's Tariff
331 Destination is blocked in Terminator's Tariff
332 Originator was found by IP but tech prefix does not match
333 Originator was found by IP but the port does not match
334 Source number is in blacklist
335 Source number is not in the whitelist
336 Destination can not be empty
337 Call comes from the server which is not assigned to the originator
338 Unreachable Terminator skipped (Periodic Check is enabled)
339 User is not allowed to dial through own terminators
340 User's call rate is higher than allowed
341 Originator's IP is unknown
342 Global Incoming System CPS limit reached
343 Too many hops


All M2 HGC return SIP 503 by default.

This can be changed in /etc/m2/system.conf using

hgcX = code

Where X is M2 HGC, and code is ITU-T Q.850 Code and then execute command:

m2 reload



See also